Türkaytech UAV Türkaytech İHA
Two competition seasons on a student team building a fixed-wing UAV for Teknofest. My responsibilities were structural design, aerodynamic analysis and material selection, together with manufacturing coordination and component assembly.
What the competition actually constrains
A competition aircraft is not designed against a performance target in isolation. It is designed against a rulebook, a mission profile and a date. Mass budget, span limits and the mission sequence set the envelope before any aerodynamics begins, and the date decides how much iteration the team can afford. Most of the engineering judgment goes into choosing which analyses are worth running in the time available.
Structure and materials
- Load paths laid out around the wing spar and its attachment, which is where a competition airframe fails if it is going to.
- Composite material selection driven by what could actually be manufactured and repaired by the team between flights, not by the best laminate on paper.
- Component layout fixed early so that centre of gravity stayed inside its range as subsystems changed mass during the season.
Aerodynamic analysis
CFD was used to compare candidate configurations and to check behaviour at the edges of the flight envelope rather than to chase a final drag number. On a student timeline the value of the analysis is in ruling options out early, before anything is cut.
Manufacturing and assembly
I coordinated the fabrication of parts across suppliers and the workshop and took part in assembly. This was the part of the project that taught me the most: a design that is correct and cannot be built in the time remaining is not correct. The habit of asking "who makes this, with what, and how long does it take" before finalising a geometry started here and has stayed with me in production engineering.
What I took from it
Working to a competition deadline with a team is the closest thing an undergraduate gets to a real project schedule. It is also where I first saw that the bottleneck in a technical project is rarely the technical part — it is the handovers between people, which is the same observation that later led me to build production software.
Teknofest için sabit kanatlı bir İHA geliştiren bir öğrenci takımında iki yarışma sezonu. Sorumluluk alanlarım yapısal tasarım, aerodinamik analiz ve malzeme seçimi; bunların yanında imalat koordinasyonu ve parça montajıydı.
Yarışmanın gerçekte koyduğu kısıtlar
Bir yarışma hava aracı, tek başına bir performans hedefine karşı tasarlanmaz. Bir şartnameye, bir görev profiline ve bir tarihe karşı tasarlanır. Kütle bütçesi, açıklık sınırları ve görev dizisi, aerodinamiğe başlamadan önce zarfı belirler; tarih ise takımın kaç iterasyona gücünün yeteceğine karar verir. Mühendislik kararının büyük kısmı, eldeki sürede hangi analizlerin yapmaya değer olduğunu seçmeye gidiyor.
Yapı ve malzeme
- Yük yolları kanat kirişi ve onun bağlantısı etrafında kuruldu; bir yarışma gövdesi kırılacaksa orada kırılır.
- Kompozit malzeme seçimi, kâğıt üstündeki en iyi lamine yerine takımın uçuşlar arasında gerçekten üretip onarabileceği şeye göre yapıldı.
- Komponent yerleşimi erken sabitlendi; böylece sezon boyunca alt sistemlerin kütlesi değişirken ağırlık merkezi aralığında kaldı.
Aerodinamik analiz
CFD, nihai bir sürükleme sayısının peşine düşmek için değil, aday konfigürasyonları karşılaştırmak ve uçuş zarfının uçlarındaki davranışı kontrol etmek için kullanıldı. Öğrenci takvimine göre analizin değeri, hiçbir şey kesilmeden önce seçenekleri erken elemekte.
İmalat ve montaj
Parçaların tedarikçiler ve atölye arasında imalatını koordine ettim ve montajda yer aldım. Projenin bana en çok öğreten kısmı buydu: doğru olan ama kalan sürede üretilemeyen bir tasarım doğru değildir. Bir geometriyi kesinleştirmeden önce "bunu kim, neyle yapıyor ve ne kadar sürüyor" diye sorma alışkanlığı burada başladı ve imalat mühendisliğinde de benimle kaldı.
Geriye kalan
Bir takımla yarışma tarihine çalışmak, bir lisans öğrencisinin gerçek bir proje takvimine en çok yaklaştığı şey. Aynı zamanda teknik bir projedeki darboğazın nadiren teknik kısım olduğunu ilk gördüğüm yer — darboğaz insanlar arasındaki devirlerdi; bu da sonradan beni üretim yazılımı yazmaya götüren gözlemin aynısı.