Aerodynamic performance analysis of wind turbine systems Rüzgar türbini sistemlerinin aerodinamik performans analizi
A computational study of how blade geometry changes the aerodynamic performance of a horizontal axis wind turbine, carried out in ANSYS Workbench and Fluent. The output is a dataset of flow fields, thrust and torque across blade configurations, prepared for an academic article.
Question
Blade geometry decisions are usually justified with correlations and one-dimensional momentum theory. Those methods are fast and they are adequate near the design point — but they say very little about what happens at the root and the tip, where the flow is three-dimensional and separation starts. The question this study takes on is how much of the performance difference between configurations is actually explained by those regions.
Method
- Geometry prepared parametrically so that configurations differ in a controlled way rather than being modelled independently.
- Rotating reference frame for the steady cases; a single blade passage with periodic boundaries where the configuration allows it, to keep the cell count tractable.
- Mesh refinement concentrated on the boundary layer and the tip region, with the near-wall resolution chosen to match the turbulence treatment rather than a fixed target.
- Mesh convergence established per configuration, not once for the family — a mesh that resolves one geometry is not automatically adequate for the next.
- Thrust and torque integrated over the blade surface; flow fields exported for comparison between configurations at matched operating conditions.
Running the cases
The study is parametric, which means the same sequence of operations repeated across dozens of cases. Doing that by hand is both slow and a source of inconsistency, so the runs are driven by CFD Flow — an agent that operates ANSYS Workbench through its normal interface, runs project batches and exports the reports. The scientific content is unaffected; what changes is that every case is set up the same way.
Status
Dataset in preparation for publication. The planned next phase, after the article, is a biomimetic blade design and a performance comparison against the baseline configurations.
Contour plots and the convergence study will be added here once the article is submitted.
Yatay eksenli bir rüzgar türbininde kanat geometrisinin aerodinamik performansı nasıl değiştirdiğine dair ANSYS Workbench ve Fluent ile yürütülen sayısal bir çalışma. Çıktı; akademik bir makale için hazırlanan, farklı kanat konfigürasyonlarına ait akış alanı, itki ve tork veri setidir.
Soru
Kanat geometrisi kararları genellikle korelasyonlar ve tek boyutlu momentum teorisiyle gerekçelendirilir. Bu yöntemler hızlıdır ve tasarım noktası civarında yeterlidir — ama akışın üç boyutlu olduğu ve ayrılmanın başladığı kök ve uç bölgelerinde çok az şey söyler. Bu çalışmanın ele aldığı soru, konfigürasyonlar arasındaki performans farkının ne kadarının gerçekte bu bölgelerle açıklandığıdır.
Yöntem
- Geometri parametrik hazırlandı; konfigürasyonlar birbirinden bağımsız modellenmek yerine kontrollü biçimde farklılaşıyor.
- Kararlı durum çözümleri için dönen referans çerçevesi; konfigürasyonun izin verdiği yerde hücre sayısını makul tutmak adına periyodik sınırlarla tek kanat geçişi.
- Ağ sıklaştırması sınır tabaka ve uç bölgesinde yoğunlaştırıldı; duvara yakın çözünürlük sabit bir hedef yerine kullanılan türbülans yaklaşımına göre seçildi.
- Ağ yakınsaması aile için bir kez değil, her konfigürasyon için ayrı kuruldu — bir geometriyi çözen ağ, bir sonraki için otomatik olarak yeterli değildir.
- İtki ve tork kanat yüzeyi üzerinden integre edildi; akış alanları eşleştirilmiş çalışma koşullarında karşılaştırma için dışa aktarıldı.
Koşumların yürütülmesi
Çalışma parametrik; yani aynı işlem dizisi onlarca vaka üzerinde tekrarlanıyor. Bunu elle yapmak hem yavaş hem de tutarsızlık kaynağı, bu yüzden koşumlar CFD Flow ile yürütülüyor — ANSYS Workbench'i normal arayüzü üzerinden kullanan, proje gruplarını çalıştırıp raporları dışa aktaran bir ajan. Bilimsel içerik bundan etkilenmiyor; değişen şey her vakanın aynı şekilde kurulması.
Durum
Veri seti yayına hazırlanıyor. Makale sonrası planlanan aşama, biyomimetik bir kanat tasarımı ve bunun temel konfigürasyonlarla performans karşılaştırması.
Kontur grafikleri ve yakınsama çalışması, makale gönderildikten sonra buraya eklenecek.